Adhesives        
Acrylics
Aerosols
Anaerobics
Cyanoacrylates
Epoxies
Glue Dots
Hot Melt Adhesives
Methacrylates
Mold Releases
Sealants
Silicones
Solvent-Free
Structural Adhesives
Urethanes
UV Adhesives

   Applicators         
Accessories
Dispensers
Dual Dispensing
Epoxy
Hot Melt Dispensers
Hot Melt Bulk
Hot Melt Hoses
Hot Melt Rolls
Hot Melt Parts Nozzles/Parts
Motionless Mixers
Robots
Structural

Demonstrations

Bar Code Printer
Box Printer

Equipment
Drum Unloader
Slot Die Applicator
Cold Glue Applicator
Fiberized Spray Pattern Controllers
Bulk Meters
Drum Meters
Adhesive Feeders
Metering Station
Supply Units
   
   Applications       
Carton Sealing
Electronic Materials
Encapsulants
Green Adhesives
Magnet Bonding
Marine Adhesives
Medical Device
One Part Adhesives
Packaging
Potting
Robotic
Solvent-Free Spray
Space Age Adhesive
Surfacing Adhesives
Transportation
Woodworking

Literature                
About Bonding
Data Sheets
Journals
Line Card
MSDS
Tech Menu

      
Meeting Customer expectations
and requirements is the main objective
 of   ISO 9001:2008
 

Customer Survey
 We would appreciate your help so that we can provide you with the very best in services. Your response will help us address the areas of performance needing improvement.

             
You may print this page for your file

Hysol ® 0430 Red
Hot Melt Adhesive

 Description
Hysol Spraypac™ 0430 Red is formulated to be spray applied to a wide variety of substrates using the Hysol 4210 Spray Tool™.   SprayPac 0430 Red is suitable for bonding expanded polystyrene or urethane foams, corrugated, wood, fabrics and plastics. SprayPac 0430 Red can be used in most applications where solvent-based aerosols are used. The adhesive is available red tinted Polyshot cartridges.


Typical Properties
Test Method
Softening Point, RB, F                                         240                            ASTM E28
Viscosity @ 330F, cps                                           6,250                         ASTM D3236
               @ 350F                                                  4,000          
               @ 375F                                                  2,950
               @ 400F                                                  2,100
Heat Resistance, Pine, 2 psi load                         170                             ASTM D 4498 (2 lbs.)
Open Time, sprayed, minutes                             3.5
Molten Tack                                                          High

Performance Characteristics
Lap Shear Strength, psi                                                                            ASTM D 3163
Pine                                                                         315
Polypropylene                                                        277
HDPE                                                                    217
Polycarbonate                                                         270

Application
Best results are achieved when sprayed 6-9" above the substrate. A one inch high pattern is optimum. Adjust set screw on the Hysol 4210 SprayToolTM counter clockwise to increase spray width or clockwise to dispense a bead.  Apply at 360F using thermostat part # EST005. Use cartridges well dusted with talc the powdery material which coats cartridges as recieved.

Availability
Polyshot Cartridges for the Spray Tool™             

Technical Consultation Service
Our technical staff and representative are ready to assist in solving any special bonding requirements. You are invited to take advantage of our extensive experience, laboratory services and trained field service staff. Call 800.767.8786 now and let us help you with your adhesive needs.

Technical Consultation Service
Our technical staff and representative are ready to assist in solving any special bonding requirements. You are invited to take advantage of our extensive experience, laboratory services and trained field service staff. Call 800.323.5158 now and let us help you with your adhesive needs.

DISCLAIMER: The information supplied in this document is for guidance only and should not be construed as a warranty. All implied warranties
are expressly disclaimed. Including without limitation any warranty of merchantability and fitness for use: All users of the materials are responsible
for assuring that it is suitable for their needs, environment and use. All data is subject to change as Dexter deems appropriate. 

Users should review the Material Safety Data Sheet (MSDS) and product label for the material to determine possible health hazards, appropriate
engineering controls and precautions to be observed in using the material. Copies of the MSDS and label are available upon request. 

For more information or to order contact the Glu Guru™ at 1-800-323-5158
or Email mike@on-hand.com