|
Adhesives
Acrylics
Aerosols
Anaerobics
Cyanoacrylates
Epoxies
Glue Dots
Hot Melt Adhesives
Methacrylates
Mold Releases
Sealants
Silicones
Solvent-Free
Structural Adhesives
Urethanes
UV Adhesives
Applicators
Accessories
Dispensers
Dual Dispensing
Epoxy
Hot Melt Dispensers
Hot Melt Bulk
Hot Melt Hoses
Hot Melt Rolls
Hot Melt Parts Nozzles/Parts
Motionless Mixers
Robots
Structural
Demonstrations
Bar Code Printer
Box
Printer
Equipment
Drum Unloader
Slot Die Applicator
Cold Glue Applicator
Fiberized Spray Pattern Controllers
Bulk Meters
Drum Meters
Adhesive Feeders
Metering Station
Supply Units
Applications
Carton Sealing
Electronic Materials
Encapsulants
Green Adhesives
Magnet Bonding
Marine Adhesives
Medical Device
One Part Adhesives
Packaging
Potting
Robotic
Solvent-Free Spray
Space Age Adhesive
Surfacing Adhesives
Transportation
Woodworking
Literature
About Bonding
Data Sheets
Journals
Line Card
MSDS
Tech Menu
Meeting Customer expectations
and requirements is the main objective
of ISO 9001:2008
Customer Survey
We would appreciate your help so that we can provide
you with the very best in services. Your response will help us address the areas
of performance needing improvement.
| |
 
You may print this page for your file
Hysol ® 0437
Hot Melt Adhesive
Description
Hysolâ SprayPacä 0437 hot melt adhesive is formulated to be spray applied to a wide variety of substrates through bulk hot melt spray equipment. Hysol 0437 is suitable for bonding polyethylene or urethane foams, expanded polystyrene, corrugated, wood, fabrics, and plastics. If smaller applications require a hand held portable hot melt applicator, Hysol SprayPacä 0430 shaped hot melt adhesive is recommended using the Hysol 4210 Spray Toolä.
Typical Properties
Test Method
Softening Point, °F 227 ASTM E 28
Viscosity @ 350oF, Cps 5,200 ASTM D 3236
Brookfield RVT, Spindle SC4-27
Open Time, Sprayed, Minutes 3.5
Specific Gravity @ 75°F, g/cc 1.03 ASTM D 792
Heat Resistance, 2lb, °F 170 ASTM D 4498
Application Temperature, °F
Tank 350
Hose and Gun 375
Performance Characteristics
Tensile Lap Shear Strength, psi ASTM D 3163
Pine 320
Polypropylene 280
HDPE 220
Polycarbonate 270
Application
Allow dispensing equipment to reach operating temperature before applying the adhesive. Hysol 0437 should be sprayed 6-9" above the substrate. The best bonding results are achieved when the substrates are bonded immediately.
Packaging
5 lb. Bricks (8 bricks/carton)
Technical Consultation Service
Our technical staff and representative are ready to assist in solving any special bonding requirements. You are invited to take advantage of our extensive experience, laboratory services and trained field service staff. Call
800.323.5158 now and let us help you with your adhesive needs.
DISCLAIMER: The information supplied in this document is for guidance only and should not be construed as a warranty. All implied warranties
are expressly disclaimed. Including without limitation any warranty of merchantability and fitness for use: All users of the materials are responsible
for assuring that it is suitable for their needs, environment and use. All data is subject to change as Dexter deems appropriate.
Users should review the Material Safety Data Sheet (MSDS) and product label for the material to determine possible health hazards, appropriate
engineering controls and precautions to be observed in using the material. Copies of the MSDS and label are available upon request.
For
more information or to order contact the Glu Guru™ at 1-800-323-5158
or Email
mike@on-hand.com
|
The Glu
Guru™
Adhesive Tech Center
